Product Details:
|
Drive Mode: | 6-250m3 | Mnr: | R909433355 |
---|---|---|---|
Rotation Speed: | 1500 - 3000 Rpm | Material No: | R910916809 |
Application: | Mobile And Industrial Machinery | Condition: | New |
Seal Type: | Lip Seal Or Mechanical Seal | Maximum Pressure: | 280 Bar |
Size: | 290*180mm |
A10VSO18DR/31L-PPA12N00 A10VSO28DRG/31R-VPA12N00 A10VSO18DR/31L-VPA12N00
A10VSO18DFR/31L-PPA12N00 A10VSO10DR/52R-PPA14N00 Rexroth axial piston pump, German made hydraulic pump
Rexroth A10VSO hydraulic pump |
1. What are the possible causes and solutions for insufficient or no oil output from the hydraulic pump? |
• Reason: |
Excessive resistance in the oil suction pipeline (such as clogged oil filter, low oil tank level, or air leakage in the inlet pipe). |
Internal leakage of the pump (scratches on the oil distribution plate, poor sealing, sand holes, etc.). |
The inclination angle of the inclined plate is too small and the displacement is insufficient. |
Motor reversal (requires adjustment of phase sequence). |
• Solution: |
Clean the oil filter, add oil to the normal liquid level, and check the sealing of the pipeline. |
Replace worn parts (such as plungers, oil distribution plates) or grind mating surfaces. |
Adjust the variable piston to increase the inclination angle of the inclined plate. |
2. How to adjust if there is still traffic output at the median level? |
Reason: Deviation, looseness, or wear of the control mechanism (such as wear of the inclined plate ear shaft). |
Solution: Reset the controller, tighten or replace damaged parts, and check the angle holding force. |
How to troubleshoot the high vibration and noise during pump operation? |
• Mechanical reasons: |
The pump and motor shaft are not concentric, the coupling is damaged, or the bolts are loose. |
Wear of bearings or variable head bearings (dry friction or impurities in the oil during start-up). |
• Hydraulic reasons: |
The oil inlet pipe is too thin, the oil filter is clogged, or the oil viscosity is too high. |
• Solution: |
Reinstall and replace worn parts. |
Select appropriate oil to ensure smooth fuel tank design and piping. |
What are the causes and solutions for overheating of the pump body? |
• Reason: |
Mechanical friction (such as improper clearance between moving parts) or liquid friction (high-pressure oil leakage converted into thermal energy). |
Filter blockage leads to excessive back pressure in the return oil. |
• Solution: |
Adjust the gap and increase the capacity of the cooler or fuel tank. |
Clean or replace the filter. |
How to solve the problem of oil leakage? |
• Common oil leakage points: |
Damaged spindle oil seal, internal leakage (high oil seal pressure), loose external pipeline or aging sealing gasket. |
• Solution: |
Replace the oil seal or defective shaft, check the size of the oil drain pipe, and tighten the joint. |
What are the key points of daily maintenance? |
• Oil management: |
Maintain oil temperature at 25-60 ℃, cleanliness level ≥ 8, and regularly test oil quality. |
• Regular inspection: |
Conduct a comprehensive inspection of seals, filters, and mechanical components every 6 months. |
After running for 3000 hours, it is necessary to check the status of the oil replenishment pump daily. |
Before starting: Ensure that the pump is filled with oil to avoid dry friction. |
How to adjust abnormal pressure (too high/too low)? |
• Low pressure: Check for pipeline leaks, overflow valve faults, or cylinder block distribution plate leaks. |
Excessive pressure: Adjust the overflow valve, check the directional valve or return oil pipeline. |
------ |
precautions |
Installation requirements: The concentricity between the pump shaft and the motor shaft should be less than 0.05mm, and the suction height should not exceed 500mm. |
• Spare parts replacement: It is recommended to use original seals and wear-resistant components to ensure compatibility. |
FAQ:
What are the common applications of Rexroth piston pumps?
Rexroth piston pumps are used in:
• Construction machinery (excavators, cranes)
• Industrial hydraulics (presses, injection molding machines)
• Marine and offshore equipment
• Wind turbines and renewable energy systems
• Mobile hydraulics (agricultural and forestry machinery)
4. How do I select the right Rexroth piston pump for my application?
Consider the following factors:
• Flow rate & pressure requirements
• Fixed or variable displacement needs
• Control type (mechanical, hydraulic, or electronic)
• Mounting configuration
• Environmental conditions (temperature, contamination risk)
Consult Rexroth technical documentation or contact authorized distributors for assistance.
Contact Person: Mr. liyun
Tel: +8615280488899