|
제품 상세 정보:
|
| 드라이브 샤프트: | 키가 있는 테이퍼형 1:5(Ø17mm) | 포트 연결: | 사각 플랜지(ISO 8434-1) |
|---|---|---|---|
| 장착 플랜지: | 직사각형 플랜지, Ø80mm | 주택 자료: | 알류미늄 |
| 무게: | 대략. 3.2~3.8kg |
|
Parameter |
Specification |
|---|---|
|
Manufacturer Part No. |
0510225006 |
|
Pump Type |
External Gear Pump, Fixed Displacement |
|
Series / Platform |
AZPF Series F (High Pressure) |
|
Geometric Displacement |
4.0 cm³/rev |
|
Rotation (viewed from shaft end) |
Clockwise (Right-Hand) |
|
Pressure Ratings |
Max. Continuous: 250 bar |
|
Speed Range |
Recommended: 1000 - 4000 rpm |
|
Drive Shaft |
Tapered 1:5 with Key (Ø17 mm) |
|
Port Connection |
Square Flange (ISO 8434-1) |
|
Mounting Flange |
Rectangular Flange, Ø80 mm |
|
Housing Material |
Aluminum |
|
Sealing Material |
NBR (Standard), FKM (Shaft Seal) |
|
Weight |
Approx. 3.2 - 3.8 kg |
|
Hydraulic Fluid |
Mineral-based oils (HL, HLP) |
|
Viscosity Range |
10 - 300 mm²/s (Optimal: 20 - 100 mm²/s) |
|
Fluid Cleanliness |
NAS 1638 Class 10 (Recommended: Class 9) |
Q: What does the model code "AZPF-1X-004RCB20KB" mean?
A: It decodes as follows:
AZPF: Series code for high-pressure external gear pumps.
1X: Frame size / bearing specification.
004: Geometric displacement (4.0 cm³/rev).
R: Clockwise rotation.
C: Tapered shaft 1:5.
B20: Port and flange configuration (Square flange per ISO 8434-1).
KB: Variant code for seals and covers.
Q: Is this pump suitable for high-pressure applications?
A: Yes. The AZPF series is designed for heavy-duty use. This model can handle continuous pressures up to 250 bar and intermittent peaks up to 280 bar, making it ideal for industrial machinery and mobile hydraulics.
Q: Can I get this pump in counter-clockwise rotation?
A: Yes. Rexroth typically offers a left-hand rotation version (denoted by an 'L' in the suffix, e.g., ...LCB...). Always verify the rotation direction before installation.
Q: What is the recommended operating viscosity?
A: Operate within 10 to 300 mm²/s. For optimal efficiency and service life, maintain viscosity between 20 and 100 mm²/s. Avoid prolonged operation below 10 mm²/s to prevent internal wear.
Q: What is the minimum speed at maximum pressure?
A: To ensure adequate lubrication of the sliding bearings, the minimum speed should be 1200 rpm when operating at the maximum continuous pressure (250 bar). Running slower than this under high load can cause premature failure.
Q: How do I calculate the flow output?
A: Use the formula:
Flow (L/min) = Displacement (4.0 cm³/rev) × Speed (rpm) / 1000
Actual flow will be slightly less due to volumetric losses (typically 90-95% efficiency).
Q: What are common failure signs?
A: Watch for:
Noise: High-pitched whining indicates cavitation (check inlet suction); knocking suggests bearing wear.
Reduced Flow: Often caused by worn gears or side plates due to contamination.
External Leakage: Usually from the shaft seal (FKM), often due to age or excessive shaft play.
Q: Can this pump be repaired in the field?
A: While Rexroth provides seal kits, the AZPF pump uses precision sliding bearings and pressure-compensated side plates. Replacing seals is possible, but rebuilding the internal gear set requires specialized tools and pressure testing. For critical applications, an exchange unit is often recommended.
Q: What is the #1 cause of premature failure?
A: Oil contamination. This pump requires very clean oil (NAS Class 9-10). Always use a pressure filter with a beta ratio (β10) ≥ 100. Running with a clogged suction filter or low oil level can cause cavitation and catastrophic damage.
Disclaimer: This data is based on standard Rexroth documentation for the AZPF series. Always refer to the official RE 10 250 datasheet for your specific application and safety guidelines.
담당자: Mr. liyun
전화 번호: +8615280488899
Korean
