|
Szczegóły Produktu:
|
| Stosowanie: | Olej, hydrauliczna pompa tłokowa | Aplikacja: | Dozowanie, inne, układ hydrauliczny, pompy hydrauliczne, koparka |
|---|---|---|---|
| Struktura: | Pompa tłokowa, pompa zębata, pompa jednostopniowa, pompy hydrauliczne | Funkcja: | Wysoka wydajność, długie życie |
| Typ: | Agregaty hydrauliczne, A8VO55/80/107/160, Pompa hydrauliczna Rexroth, A8VO80LA1KH1/63R1 | Nazwa: | Pompa tłokowa Rexroth, pompa 90R100, części pompy koparki pompy hydrauliczne Rexroth |
| Pochodzenie: | Shandong, Chiny, w 100% oryginalna pompa zębata Rexroth | ||
| Podkreślić: | Rexroth hydraulic directional valve,German made electro-hydraulic valve,original imported proportional valve |
||
4WRZ16W6-150-7X/6EG24N9TK4/M
4WRZ16W6-150-7X/6EG24N9ETK4/D3M
4WRZ16W6-150-7X/6EG24N9ETK4/M
German-made original imported hydraulic directional valve with proportional control
| Selection Dimension | Specific Parameters/Options | Description |
|---|---|---|
| Model Designation | 4WRE | Direct-acting proportional directional valve with electrical position feedback and no integrated electronics (OBE) |
| Integrated Electronics (OBE) | No Code | Standard configuration without integrated electronics; external amplifier required |
| Nominal Size | 6 | Core size with component series 2X; mounting dimensions comply with Series 20-29 standards |
| Valve Core Type | 4/2 (2-position 4-way), 4/3 (3-position 4-way) | 4/3 type features spring-centered spool for automatic reset when de-energized |
| Rated Flow (Δp=10bar) | 4L/min (Code 04), 8L/min (Code 08), 16L/min (Code 16), 32L/min (Code 32) | Flow rates distinguished by corresponding codes |
| Seal Material | V (FKM Fluororubber) | Compatible with mineral oil and other hydraulic fluids |
| Power Supply Voltage | G24 (DC 24V) | Industrial standard DC power supply |
| Electrical Interface | A1 (±10V Voltage Input), F1 (4-20mA Current Input) | Compatible with PLCs, computers, and other control signal sources |
| Electrical Connection | K4 (No Plug) | Plug compliant with DIN EN 175301-803 standard required |
| Special Protection | J (Seawater-Resistant) | Only available for Size 6; suitable for marine-related or humid/corrosive conditions |
| Mounting Standard | ISO 4401 | Panel mounting with standard mounting hole pattern |
| Maximum Working Pressure | 315bar | Suitable for medium-to-high pressure industrial hydraulic scenarios |
Yes, integrated electronics (IPE) models include short-circuit protection, which shuts down the coil if a short is detected, preventing damage.
Shielded cables are recommended to reduce electromagnetic interference (EMI), especially in industrial environments with high electrical noise. Ground the shield at one end only.
Fluid temperature should be between -20°C and +60°C (-4°F to +140°F); temperatures above 60°C may accelerate seal wear and reduce fluid viscosity.
Optimal viscosity is 20-40 mm²/s (cSt). Viscosity below 10 mm²/s may cause leakage, while viscosity above 100 mm²/s may increase pressure drop and reduce response time.
Yes, a 25 μm absolute filter (β100 ≥ 75) is mandatory in the supply line to prevent contamination of the valve's internal components.
Yes, water contamination (exceeding 0.1%) can cause corrosion, seal degradation, and clogging. Use water-separating filters and monitor fluid moisture levels.
Osoba kontaktowa: Mr. liyun
Tel: +8615280488899
